Sample Unfinished Wood Custom Cabinet Doors

Sample custom unfinished 12"w x 15"h wood cabinet doors
Design your own sample cabinet doors and drawer fronts and have them shipped, ready to finish

Due to lumber and construction market conditions, lead time:  7-8 weeks for production
(All lead times are subject to variations in workload)

Your price will be calculated based on option selections.  All sample doors are 12" x 15" only

The illustrations below represent typical cabinet doors.

Unfinished cabinet doors and drawer fronts are sanded to 220 prior to shipping.  (see finishing specifications for details)

Our cabinet doors and drawer fronts can also be shipped finished and you can choose from a wide variety of stain and glaze colors. 

Design Sample Cabinet Doors
(Model numbers are listed below style pictures)

Raised, Recessed and Grooved Panel Doors
7½" x 7½" minimum w x h 2-5/16" Framing Slant raise shown Select Reverse G-Cove for recessed panel	8¼" x 9¼" minimum w x h 2-5/16" Framing Slant raise shown Select Reverse G-Cove for recessed panel	8¼" x 8½" minimum w x h 2-5/16" Framing Slant raise shown Select Reverse G-Cove for recessed panel
CRP10	CRP20	CRP30
12-7/8" x 7½" minimum w x h 2-5/16" Framing Slant raise shown Select Reverse G-Cove for recessed panel	6" x 7-1/2" minimum w x h Battens are attached to back or can be shipped loose	12-7/8" x 12-7/8" minimum w x h 2-5/16" Framing Slant raise shown Select Reverse G-Cove for recessed panel
CRP10102	Flush Batten	CRP10103
Shaker Style Doors
7" x 6¾" minimum w x h 2-5/16" Framing 3/8" Reverse G-Cove raise shown	7" x 5" minimum w x h 2-5/16" Framing Std 1/4" veneered MDF core panel shown (Select CRP-10 for "Knotty" or Soft Maple mat'l)	11-3/8" x 6¾" minimum w x h 2-5/16" Framing 3/8" Reverse G-Cove raise shown
Albany	TW-10	Sheldon
Grooved Panel Doors (Grooved Panels REQUIRE selection of Reverse G-Cove Panel Raise)
7" x 6¾" minimum w x h 2-5/16" Framing 3/8" Reverse G-Cove raise shown G-015 rout - 1½" spacing	6¾" x 6¾" minimum w x h 2-5/16" Framing 3/8" Reverse G-Cove raise shown G-121 rout - 2" spacing	7" x 6¾" minimum w x h 2-5/16" Framing 3/8" Reverse G-Cove raise shown G-012 rout - 1½" spacing
Ardmore	Woodford	Yardley

Select Sample Door Material

Alder	Alder, Knotty	Birch, White*	Cherry*
Cherry, Rustic	Maple, Hard*	Maple, Hard Rustic	Maple, Soft
Oak, Red*	Oak, Red, Qtr Sawn	Oak, Red, Rustic	Oak, White*
Oak, White, Qtr Sawn	Paint Grade Hard Maple	Hickory*	Hickory, Rustic
Pine, Knotty*	Walnut*
* Premium Grade is available

The next 3 steps will address the framing bead, framing edge and panel raise choices for custom doors.  Slab Style doors will require framing edge choice only.

Choose Sample Door Framing Edge
(For all drawer front styles)

B No hinge boring Rabbet 7/16" deep 3/8" high	B-2* Hinge boring okay	C No hinge boring Rabbet 7/16" deep 3/8" high	C-2 No hinge boring	CFP No hinge boring
CFP-2* Hinge boring okay	E-2 No hinge boring	FEP** Finished End Panel Rabbet 11/16" deep 3/16" high	FP No hinge boring	H No hinge boring Rabbet 7/16" deep 3/8" high
H-2* Hinge boring okay	J-2 No hinge boring	L-034* Hinge boring okay	L-059* Hinge boring okay	L-061 No hinge boring
L-120 No hinge boring	L-149* Hinge boring okay	L-253 No hinge boring 5 degree back bevel	L-281* Hinge boring okay	L-297*² Hinge boring okay
L-304² No hinge boring	L-686 No hinge boring 5 degree back bevel	L-772 No hinge boring	L-803* Hinge boring okay	LC-2* Hinge boring okay
LC-Inset*² Hinge boring okay	Machine Edge* Hinge boring okay	PRS-2* Hinge boring okay	RC-2 No hinge boring	V-2 No hinge boring

(Click to enlarge)

(Click to enlarge)

* indicates edge profiles which can be bored for concealed hinges
² indicates a premium edge which will result in additional charge per door

Some edge profiles are NOT recommended for use with Euro, demountable or Inserta style hinges, note hinge boring notes under each profile.

Edges displayed above are computer generated to represent the actual product as closely as possible but may not be exact.  If you are seeking an exact match, contact us for a sample.

Choose Sample Door Framing Bead

(Click to enlarge)

Choose Sample Door Panel Raise Style

(Click to enlarge)

Solid wood panels may be comprised of multiple pieces of wood joined together to achieve the necessary width.  Inverted panel IP115 is charged as raised panel plus the additional charge reflected above in the option menus.  Doors 45" tall and greater will have a center rail installed (RP120) to help prevent warpage (unless otherwise specified).

Panel Choices If Selecting Grooved Doors

You must select the Reverse G-Cove from the Panel Raise Menu

G-012 1½" spacing center to center Groove width 1/4" Groove depth 1/16"	G-121 1½" spacing center to center Groove width 1/4" Groove depth 1/8"	G-015 ¾" or 1½" spacing center to center  Groove width 3/32" Groove depth 3/64"

Hinge Boring Options

If you intend to use a concealed European style hinge, here are your boring options.  We normally recommend a compact style hinge if you have "Face Frame" style cabinets.  If you have any questions, just give us a call. 

• Doors 9" to 42" receive two bores
• Doors 42-1/16" to 72" receive three bores
• Doors 72-1/16" and longer receive four bores with center holes set 25" in from each end.
• Bore hole is 35mm diameter, 13.5mm deep and the insert holes are 8mm diameter and 11.9mm deep
• Custom boring is available at additional cost per door (contact customer service)
• Dowel inserts are not included with any door.  The dowel inserts come with the hinge or can be purchased separately.

For Face Frame Cabinets Using Compact Hinges
Compact Style Hinge for "A" boring
Compact hinge bore with dowel inserts Select ("A" with) Placement is 3" to center from top and bottom of door	Compact hinge bore without dowel inserts Select ("A" without) Placement is 3" to center from top and bottom of door
For Face Frame Cabinets Using Long Arm Hinges
Long Arm Style Hinge for "B" & "C" boring
Long Arm hinge bore with dowel inserts Select ("B" with) Placement is 3" to center from top and bottom of door	Long Arm hinge bore without dowel inserts Select ("B" without) Placement is 3" to center from top and bottom of door
For Frameless Cabinets Using Long Arm Hinges
Long arm hinge bore pattern with dowel inserts Select ("C" with) Placement is 3-3/4" to center from top and bottom of door	Long arm hinge bore pattern without dowel inserts Select ("C" without) Placement is 3-3/4" to center from top and bottom of door

Optional Hand or Finger Pulls

Back Side Routed Finger Pulls (priced per door)

(Click to enlarge)

Hand Pull Specifications: Hand pull routs are on the back side of the door and are minimally noticeable from a front view. Specify location: Bottom left (BL), Bottom Right (BR), Bottom Center (BC), Top Left (TL), Top Right (TR) or Top Center (TC) Rout is 3-5/8" wide and 3/8" deep. When specified as right or left, the rout begins 3" from the edge of door. Rout is centered on doors less than 10" wide. Not available with the following edge profiles:  E-2, FP, L-253, L-304, L-686, L-947 and RC-2 Adds one day to lead time.

Product Warranty Information

Information about Conestoga product and finishing warranties.

Allowable tolerances for bow, warp or twist for single panel, multi-panel, frame only and mullion doors are as follows:

• Single panel up to 26" wide and 48" tall - 1/8"
• Multi-panel up to 26" wide and 48-1/16" to 64-15/16" tall = 1/4"
• Multi-panel up to 26" wide and 65" to 83-15/16" tall = 5/16"
• Single panel, single opening frame only and mullion doors over 26" wide and 48" tall will not be warranted (mullion lites not to be included in opening count)
• Any door exceeding 25-15/16" wide or 83-15/16" high will not be warranted.

Allowable tolerances for contraction, expansion and warpage for one and three piece products are:

• Up to 12" wide and 21-15/16" high - 1/8"
• 12-1/16" to 22" wide or 22" to 43-15/16" high - 1/4"
• Any one piece product exceeding 22" wide or 43-15/16" high will not be warranted
• All three piece products over 30" wide and 14" high are not warranted

Finishing Notes

When ordering unfinished, doors should be properly prepared prior to applying any finishing products.  Be sure to read and understand the instructions provided by your finish manufacturer.  You may need to perform additional sanding to prepare your products for finishing.

Cabinet doors are your way to reflect your personal vision on the look and feel of your kitchen.  By selecting new cabinet doors for new construction or replacement cabinet doors for remodeling, you will find that your kitchen becomes your personal space in a whole new way.  Your custom cabinet doors are available in a great selection  of wood species which you will finish with your chosen stain, paint or finish. 

If you need sample kitchen doors to try in your home, you may want to buy a full size door which can be used in your project, or you may order any size you prefer. 

(Click on link or image above for measuring guide).

Special Handling Charges For Oversize Products