Custom Design RTF Cabinet Doors

You are guaranteed to find the perfect door style with our extensive selection of Shaker, contemporary and traditional thermofoil doors and drawer fronts.  Our 1 piece components are available in any of our standard thermofoil offerings in matte and satin foils.  You will appreciate the superior color consistency and quality of our thermofoil doors.

RTF Thermofoil doors and drawer fronts are grouped below into complexity groups and are priced by the number of "passes" that the equipment must make in order to cut your door style.

Special Note:  This manufacturer has a minimum order requirement and product orders less than $37 will have a "Small Order Fee" of $15 added to the order during checkout.

(Products offered by other manufacturers, shipping and handling charges do not apply toward the $37 manufacturer minimum.  Actual charge for your selection will be shown after you "Add to cart")

The "Step by Step" guide below offers information about your selection options to be chosen in the menus above.  Cabinet doors and drawer fronts will have a minimum charge of 1 square foot.  Warranty information below.

Choose Your Cabinet Door Style

Door Design Style
Square Style	Arched Style (Arch Applies To Doors Only)	Cathedral Style (Arch Applies To Doors Only)
Rounded Corner Patterns Will Be Used On ALL 2-Pass Profiles
ALL Drawer Fronts Will Be "Square Style" Regardless Of Your Design Selection

Choose Your Center Panel Route

"2 Pass" Center Panel Route Designs
A109 Door Drawer Front	A157 Door Drawer Front	A174 Door Drawer Front	A201 Door Drawer Front	A358 Door Drawer Front
"Square Style" Minimum Size Specs
Doors - 7 1/2"w x 7 1/2"h Drawer Fronts - 7 1/2"w x 5 1/2"h (Drawer Fronts Have 1" Top/Bottom Rails)	Doors - 8"w x 8"h Drawer Fronts - 8"w x 6"h (Drawer Fronts Have 1" Top/Bottom Rails)	Doors - 7 1/4"w x 7 1/4"h Drawer Fronts - 7 1/4"w x 5 1/4"h (Drawer Fronts Have 1" Top/Bottom Rails)	Doors - 8 3/8"w x 8 3/8"h Drawer Fronts - 8 3/8"w x 6 3/8"h (Drawer Fronts Have 1.05" Top/Bottom Rails)	Doors - 7 11/16"w x 7 11/16"h Drawer Fronts - 7 11/16"w x 5 11/16"h (Drawer Fronts Have 1.10" Top/Bottom Rails)
"Arch Style" & "Cathedral Style" Minimum Size Specs
Doors - 7 1/2"w x 10 5/8"h	Doors - 8"w x 11 1/8"h	Doors - 7 1/4"w x 10 3/8"h	Doors - 8 3/8"w x 11 1/2"h	Doors - 7 11/16"w x 10 13/16"h
Rounded Corner Patterns Will Be Used On ALL 2-Pass Profiles
ALL Styles Maximum Specs 48"w/h x 96"w/h Maximum Dimensions Warranted 31"w/h x 60"w/h

Select Your Outer Framing Edge Profile

Framing Edge Profiles
No Finger Pull Available
No Finger Pull Available			No Finger Pull Available
The Drawings Above Represent The Edge Profiles As Closely As Possible & May Not Be To Scale.  If Dimensions Are Critical, Consider Ordering A Sample Door Or Drawer Front.

Select Your Color

Hinge Boring Options

If you intend to use a concealed European style hinge, here are your boring options.  We normally recommend a compact style hinge if you have "Face Frame" style cabinets.  If you have any questions, just give us a call. 

Hinge Bore Patterns
Standard Number Of Hinge Bores Based On Door Height
Doors <9" to 35 -15/16" receive two bores Doors 36" to 59-15/16" receive three bores with equally spaced holes Doors 60" and longer receive four bores with equally spaced holes Bore hole is 35mm diameter, 1/2" deep and the insert holes are 8mm diameter Custom boring location is available at additional cost per door (select custom boring option and we will contact you for bore pattern dimensions)

Optional Finger Pull

Finger Pull Details

Finger Pull Cutouts Will Be On Top AND Bottom Of Doors & Drawer Fronts

Special Notes: (Cabinet doors and drawer fronts will have a minimum size charge of 1 square foot)

• Components manufactured by Northern Contours are warranted against defects occurring in the material or manufacturing process under normal use for 5 (FIVE) years from the date of original purchase. Complete warranty certificate information is available at www.northerncontours.com or can be obtained by contacting Customer Service at 877-998-1814.
• Products manufactured outside normal specifications are not covered by the warranty. Products are not warranted if exposed to excessive heat. Proper installation of heat shields between components and ovens or between components and lighting that generates high temperatures is recommended.
• Warranty covers repair or replacement of product only. Northern Contours' liability will not exceed the invoiced amount of the product.
• Remove the protective peel coat from product promptly after installation. Exposure to sun will make the peel coat difficult to remove. Adhesive residue can be cleaned with mineral spirits.
• Our manufacturing tolerance is ±1/32" or 1 mm. Warp specification is 1.5 mm per lineal foot. Warp is measured with the door on the cabinet with hinges fully adjusted. We recommend storing all raw components in a temperature-controlled environment upon delivery.
• Wood veneer variations in color and grain pattern are natural characteristics of wood and are not considered defects; therefore they are not covered under warranty.

Special Handling Charges for Oversize Products

Shipping companies do charge extra for "oversize" packages or packages that exceed certain lengths or other measurements.

If your product is going to incur additional charges, we will get a shipping quote prior to finalizing your order.  The shipping shown on your order may or may not include these "oversize" charges.  We will notify you prior to placing your order in production.

FedEx Oversize Packages

Packages that weigh 150 pounds or less and exceed 108 inches in length or 130 inches in girth (2 x width) + (2 x height) are considered “oversize” packages. Oversize packages are rated based on the greater of the package's actual rounded weight or dimensional weight. All oversize packages will have a minimum billable weight of 90 pounds in addition to any oversize package surcharge(s).  As of 2020, this surcharge will be $120 per oversize package.

Fedex Peak Oversize Package Surcharge

During peak shipping season (10/21 until 1/5), any package shipped during this period will incur an additional "Peak Oversize" charge of $37.50 per oversize package.

UPS Oversize Packages

A Large Package Surcharge will be applied to each UPS package when its length plus girth [(2 x width) + (2 x height)] combined exceeds 130 inches, but does not exceed the maximum UPS size of 165 inches. Large Packages are subject to a minimum billable weight of 90 pounds in addition to any oversize package surcharge(s).  As of 2020, this surcharge will be $115 per oversize package.

Address Changes for FedEx and UPS

Both FedEx and UPS charge for address changes and corrections.  The charge for an address change is a minimum of $16.00 as of 1/1/2019.  Please check your shipping address on your order confirmation to insure that it is correct.  The Cabinet Guy/QuikDrawers is not responsible for incorrect addresses.

If you have any specific questions, let us know or refer directly to the carrier websites for more information.

Framing and Mullion Profiles available (click on any image to enlarge)
Panel Rout Corner Specifications Rounded corner patterns will be used on all 2-Pass profiles and the A511 and A901 patterns  Square corner patterns will be used on all 3, 4 and 5-Pass profiles except A511 and A901
2 Pass Frame and Panel Design (click on any image to enlarge)
A109	A174	A201
Min/Max Sizing for Cabinet Doors Using A109, A174 & A201 Patterns (All dimensions are Width x Height)
Doors & Fronts 7.5" x 7.5" Square min 10.63" x 10.63" Arch/Cathedral min 48" x 96" max Reduced rail Drawer Fronts 7.5" x 5"	Doors & Fronts 7.25" x 7.25" Square min 10.38" x 10.38" Arch/Cathedral min 48" x 96" max Reduced rail Drawer Fronts 7.25" x 4.6875"	Doors & Fronts 8.25" x 8.25" Square min 11.25" x 11.25" Arch/Cathedral min 48" x 96" max Reduced rail Drawer Fronts 8.25" x 5.63"
3 Pass Frame and Panel Design (click on any image to enlarge)
Min/Max Sizing for Cabinet Doors Using A731 & A901 Patterns (All dimensions are Width x Height)
Doors & Fronts 8" x 8" Square min 10.5" x 10.5" Arch/Cathedral min 48" x 96" max Reduced rail Drawer Fronts 8" x 5"	Doors & Fronts 8.3" x 8.3" Square min 11" x 11"  Arch/Cathedral min     48" x 96" max Reduced rail Drawer Fronts 8.3" x 5.81"
4 Pass Frame and Panel Design (click on any image to enlarge)
A302	A401	A402
Min/Max Sizing for Cabinet Doors Using A105, A511 & A951 Patterns (All dimensions are Width x Height)
Doors & Fronts 7.7" x 7.7" Square min 10.5" x 10.5" Arch/Cathedral min 48" x 96" max Reduced rail Drawer Fronts 7.7" x 5.5"	Doors & Fronts 7.38" x 7.38" Square min 11.25" x 11.25" Arch/Cathedral min 48" x 96" max Reduced rail Drawer Fronts 7.38" x 5.38"	Doors & Fronts 9.18" x 9.18" Square min 12.25" x 12.25" Arch/Cathedral min 48" x 96" max Reduced rail Drawer Fronts 9.18" x 6.32"
A961
Min/Max Sizing for Cabinet Doors Using A961 Pattern (All dimensions are Width x Height)
Doors & Fronts 8.3" x 8.3" Square min 11.38" x 11.38" Arch/Cathedral min 48" x 96" max Reduced rail Drawer Fronts 8.3" x 5.82"

Special Notes:

Components manufactured by Northern Contours are warranted against defects occurring in the material or manufacturing process under normal use for 5 (FIVE) years from the date of original purchase. Complete warranty certificate information is available at www.northerncontours.com or can be obtained by contacting Customer Service at 877-998-1814.
Products manufactured outside our normal specifications are not covered by our warranty. Products are not warranted if exposed to excessive heat. Proper installation of heat shields between components and ovens or between components and lighting that generates high temperatures is recommended.
Warranty covers repair or replacement of product only. Northern Contours' liability will not exceed the invoiced amount of the product.
Our manufacturing tolerance is ±1/32" or 1 mm. Warp specification is 1.5 mm per lineal foot. Warp is measured with the door on the cabinet with hinges fully adjusted. We recommend storing all raw components in a temperature-controlled environment upon delivery.

(Cabinet doors and drawer fronts will have a minimum size charge of 1 square foot)

(Click on link or image above for measuring guide)

WARRANTY

Components manufactured by Northern Contours are warranted against defects occurring in the material or manufacturing process under normal use for 5 (FIVE) years from the date of original purchase. Complete warranty certificate information is available at www.northerncontours.com or can be obtained by contacting Customer Service at 877-998-1814.
Products manufactured outside our normal specifications are not covered by our warranty. Products are not warranted if exposed to excessive heat. Proper installation of heat shields between components and ovens or between components and lighting that generates high temperatures is recommended.
Warranty covers repair or replacement of product only. Northern Contours' liability will not exceed the invoiced amount of the product.
Remove the protective peel coat from product promptly after installation. Exposure to sun will make the peel coat difficult to remove. Adhesive residue can be cleaned with mineral spirits.
Our manufacturing tolerance is ±1/32" or 1 mm. Warp specification is 1.5 mm per lineal foot. Warp is measured with the door on the cabinet with hinges fully adjusted. We recommend storing all raw components in a temperature-controlled environment upon delivery.
Wood veneer variations in color and grain pattern are natural characteristics of wood and are not considered defects; therefore they are not covered under warranty.

Special Handling Charges For Oversize Products