Unfinished 5-Piece MDF Cabinet Doors & Drawer Fronts

Unfinished 5-Piece MDF Cabinet Doors & Drawer Fronts

Due to lumber and construction market conditions, lead time:  7-8 weeks for production
(All lead times are subject to variations in workload)

Select Your Design & Your Framing Edge Profile & Have Them Shipped, Ready To Finish.
Your Price Will Be Calculated Based On Your Style Selection & Size

Unfinished Cabinet Doors & Drawer Fronts Are Made Of 3/4" MDF.
(See Finishing Specifications For Details)

Select Your Door Style

5-Piece MDF Door Styles
PAY ATTENTION TO WIDTH & HEIGHT MINIMUMS TO PREVENT DELAYS IN PROCESSING
(**Cabinet Doors & Drawer Fronts Will Have A Minimum Size Charge Of 1 Square Foot**)

The next 3 steps will address the framing bead, framing edge and panel raise choices for custom doors.  Slab Style doors will require framing edge choice only.

Choose Your Framing Edge

B-2* Hinge boring okay	C-2 No hinge boring	H-2* Hinge boring okay	L-059* Hinge boring okay	L-149* Hinge boring okay
LC-2* Hinge boring okay	Machine Edge* Hinge boring okay	PRS-2* Hinge boring okay	V-2 No hinge boring

*Indicates edge profiles which can be bored for concealed hinges.

Due to the nature of MDF, all surface edges will be slightly eased to prevent chipping and damage to the edges.

Some edge profiles are NOT recommended for use with Euro, demountable or Inserta style hinges, note hinge boring notes under each profile.

Edges displayed above are computer generated to represent the actual product as closely as possible but may not be exact.  If you are seeking an exact match, contact us for a sample.

Choose Your Framing Bead

Choose Your Panel Raise Style
(CRP10 Only)

Optional Panel Groove for CRP10 Door Style
(For bead board panels only)

You must select the Reverse G-Cove from the Panel Raise Menu

G-012 1½" spacing center to center Groove width 1/4" Groove depth 1/16"

Hinge Boring Options

If you intend to use a concealed European style hinge, here are your boring options.  We normally recommend a compact style hinge if you have "Face Frame" style cabinets.  If you have any questions, just give us a call. 

• Doors 9" to 42" receive two bores
• Doors 42-1/16" to 72" receive three bores
• Doors 72-1/16" and longer receive four bores with center holes set 25" in from each end.
• Bore hole is 35mm diameter, 13.5mm deep and the insert holes are 8mm diameter and 11.9mm deep
• Custom boring is available at additional cost per door (contact customer service)
• Dowel inserts are not included with any door.  The dowel inserts come with the hinge or can be purchased separately.

For Face Frame Cabinets Using Compact Hinges
Compact Style Hinge for "A" boring
Compact hinge bore with dowel inserts Select ("A" with) Placement is 3" to center from top and bottom of door	Compact hinge bore without dowel inserts Select ("A" without) Placement is 3" to center from top and bottom of door
For Face Frame Cabinets Using Long Arm Hinges
Long Arm Style Hinge for "B" & "C" boring
Long Arm hinge bore with dowel inserts Select ("B" with) Placement is 3" to center from top and bottom of door	Long Arm hinge bore without dowel inserts Select ("B" without) Placement is 3" to center from top and bottom of door
For Frameless Cabinets Using Long Arm Hinges
Long arm hinge bore pattern with dowel inserts Select ("C" with) Placement is 3-3/4" to center from top and bottom of door	Long arm hinge bore pattern without dowel inserts Select ("C" without) Placement is 3-3/4" to center from top and bottom of door

Optional Hand or Finger Pulls

Back Side Routed Finger Pulls (priced per door)

(Click to enlarge)

Hand Pull Specifications: Hand pull routs are on the back side of the door and are minimally noticeable from a front view. Specify location: Bottom left (BL), Bottom Right (BR), Bottom Center (BC), Top Left (TL), Top Right (TR) or Top Center (TC) Rout is 3-5/8" wide and 3/8" deep. When specified as right or left, the rout begins 3" from the edge of door. Rout is centered on doors less than 10" wide. Not available with the following edge profiles:  E-2, FP, L-253, L-304, L-686, L-947 and RC-2 Adds one day to lead time.

Product Warranty Information

Information about Conestoga product and finishing warranties.

Allowable tolerances for bow, warp or twist for single panel, multi-panel, frame only and mullion doors are as follows:

• Single panel up to 26" wide and 48" tall - 1/8"
• Multi-panel up to 26" wide and 48-1/16" to 64-15/16" tall = 1/4"
• Multi-panel up to 26" wide and 65" to 83-15/16" tall = 5/16"
• Single panel, single opening frame only and mullion doors over 26" wide and 48" tall will not be warranted (mullion lites not to be included in opening count)
• Any door exceeding 25-15/16" wide or 83-15/16" high will not be warranted.

Allowable tolerances for contraction, expansion and warpage for one and three piece products are:

• Up to 12" wide and 21-15/16" high - 1/8"
• 12-1/16" to 22" wide or 22" to 43-15/16" high - 1/4"
• Any one piece product exceeding 22" wide or 43-15/16" high will not be warranted
• All three piece products over 30" wide and 14" high are not warranted

Finishing Notes

When ordering unfinished, doors should be properly prepared prior to applying any finishing products.  Be sure to read and understand the instructions provided by your finish manufacturer.  You may need to perform additional sanding to prepare your products for finishing.

Cabinet doors are your way to reflect your personal vision on the look and feel of your kitchen.  By selecting new cabinet doors for new construction or replacement cabinet doors for remodeling, you will find that your kitchen becomes your personal space in a whole new way.  Your custom cabinet doors are available in a great selection  of wood species which you will finish with your chosen stain, paint or finish. 

If you need sample kitchen doors to try in your home, you may want to buy a full size door which can be used in your project, or you may order any size you prefer. 

(Click on link or image above for measuring guide)

Special Handling Charges For Oversize Products